xm now accepts a parameter 'ioports' that accepts a hex ioport
or ioport range, in the form 02f8[-02ff]
Signed-off-by: Jody Belka <knew (at) pimb (dot) org>
xm now accepts a parameter 'ioports' that accepts a hex ioport
or ioport range, in the form 02f8[-02ff]
Signed-off-by: Jody Belka <knew (at) pimb (dot) org>
vnet-create is correct. This is better than throwing IOError, because
IOError's are currently reported as xend communication failures.
Also, fix the IOError handling at the end of the file so we don't get
a stack dump if that path is taken.
Signed-off-by: Dan Smith <danms@us.ibm.com>
on vncserver or remote X. Changeset 7547 added a test of
opts.vals.display when getenv("DISPLAY"); because there is a default
value:localhost:0, that causes the test always to be true.
Signed-off-by: Xiaofeng Ling <xiaofeng.ling@intel.com>
The problem is: There is no mechanism to detect block device setup failure
Network devices have the same problem, and are fixed with this too.
I handling this problem in the way suggested by aliguori:
- hotplug scripts write a "hotplug-status" node on store
- Xend DevController.createDevice() check verify this node and return success
or throw an exception on failure.
- If no changes in "hotplug-status" node after DEVICE_CREATE_TIMEOUT seconds
Xend throw an exception showing the problem with hotplug scripts.
Signed-off-by: Ewan Mellor <ewan@xensource.com>
list is passed rather than a single string. This expands the config-file
interface so that parameters may be passed to the network scripts from the
config file.
Fix XendRoot._logError (missing asterisk before args parameter).
In XendRoot, allow an empty configuration file. This makes it easier to unit
test code reliant on XendRoot.
Signed-off-by: Ewan Mellor <ewan@xensource.com>
for the command line parsing code in xm create. To make it easier to test,
create.py has changed in structure around the main(argv) function, adding a new
parseCommandLine function.
Remove a large number of useless parameters, where the opts structure was being
passed all over the place, just to eventually log through it. Instead two
methods -- err and warn -- have been broken out from the Opts class, and there
is now no need to pass the opts value everywhere.
Change the parsing inside make_config to remove lots of cut-and-pasted cruft.
Change the documentation to the vif command to indicate that the bridge can be
auto-detected.
Signed-off-by: Ewan Mellor <ewan@xensource.com>
This was passing down to dhclient which was keeping the 8001 port
open and preventing xend restarting.
Also fixed a case typo in setCloExec
Signed-off-by: James Bulpin <james@xensource.com>
be refused, with the domain being destroyed instead.
Further fix for reboot logic when using on_reboot=rename-restart: the incorrect
node was being removed once restart has completed, leaving Xend to conclude
later that it had crashed in the middle of a restart.
Signed-off-by: Ewan Mellor <ewan@xensource.com>
Reject the removal of -Werror from the xentop Makefile.
Reject the #include of xs.h inside xentop -- there is no need for it.
Have XendDomainInfo write domain names into /local/domain (which used to happen,
but hasn't for a little while).
Remove the dead code from xentop.c.
Signed-off-by: Ewan Mellor <ewan@xensource.com>
It doesn't make sense to undo the network configuration when stopping
xend since that would cut off all VMs from the network. Undoing the
network setup should be an option independent of xend stop.
Signed-off-by: Christian Limpach <Christian.Limpach@cl.cam.ac.uk>
whether a domain has been introduced to the store. Added a separate message
XS_IS_DOMAIN_INTRODUCED and API for that (xs_is_domain_introduced) to determine
whether the domain has really been introduced. This change means that the
tools can determine the correct domain path earlier in the domain creation
process, which is particularly a factor with live migration, as it allows us
to create the devices earlier in the process, and unpause the new domain before
performing the introduce. Until recently we already had these features, but
the simplification of the interface between xend and xenstored caused breakage.
No longer clear out the domain path when a domain is introduced -- this was a
hack to work around the recent problematic semantics of GetDomainPath.
Do not write the contents of the info block to the store. All the configuration
info is written to the /vm path, and anything else in the info block is either
dealt with explicitly or is ephemeral and has no place in the store.
Signed-off-by: Ewan Mellor <ewan@xensource.com>
/local/domain/0/backend/<devclass>/<dom>/<devid>/error, write them instead to
/local/domain/0/error/backend/<yada>. This is not the best place for them
perhaps, but it moves them out of the backend directory, on which the drivers
have a watch. This fixes the problem whereby writing an error will trigger a
watch, causing the error message to be written again, and repeat. Fixes bug
#286.
Signed-off-by: Ewan Mellor <ewan@xensource.com>
for some arguemnt like 'localtime', 'isa', device model need an argument
"-localtime", instead of "-localtime 1"
Signed-off-by: Xiaofeng Ling <xiaofeng.ling@intel.com>
1) enable ACPI in VMXAssist by default.
2) do nothing when emulating wbinvd instruction in VMXAssist.
3) use MACRO in cpu number setting/getting code.
4) remove useless parameter flags from xc_vmx_build.
5) remove usage of dsi.v_start in xc_vmx_build when not handling
vmxloader elf.
6) unmap shared_page_va when destroy VMX domain.
7) change virtual_platform_def to vmx_platform.
8) remove useless code in vmx_setup_platform.
9) change parameter of vmx_setup_platform from vcpu to domain.
10) in xen HV, vmx domain get domain processor number from the reserved
E820 area.
11) in domain.c, don't define some functions when on i386 platform or no
CONFIG_VMX.
Also removed some ugly tailing space.
Signed-off-by: Xin Li <xin.b.li@intel.com>
disabled by workaround 7468:17a9f111fa93. We additionally need to set the
FD_CLOEXEC flag on the status fd given to SrvServer when spawning the network
script, as at least on some platforms this causes xend to fail to start
properly.
Signed-off-by: Ewan Mellor <ewan@xensource.com>
