There were a couple of small bugs in the xapi xm-test:
o outdated XenAPI calls were removed from testcase
(02_xapi-vbd_basic)
o minor problem with XendLocalStorageRepository
is fixed (missed list_images() function - which
is moved from the XenQCoWStroageRepo to the common
base class XendStorageRepository)
which was detected running 02_xapi-vbd_basic.
o XenAPI session handling and connecting is fixed.
o 03_xapi-network_pos was rewritten and now uses
XenAPI.
Signed-off-by: Andreas Florath <xen@flonatel.org>
Attached there is a patch that fixes the used protocol (was udp - but
nobody was listening...) to icmp echo and added the extension, that
the dom0 and the other guest ips are also pinged.
Because of the many different scenarios (three nested loops) over
packet sizes, two guests and different ip addresses, one run of this
test case takes now about 4.5 minutes.
Signed-off-by: Andreas Florath <xen@flonatel.org>
if an additional parameter is given for the network-bridge
(e.g. netdev=eth1) The patch splits the network command into the
command name and its parameters to determine the netenv (bridge,
route, nat)
Signed-off-by: juergen.gross@fujitsu-siemens.com
In various places in documentation and code, IP addresses are provided
as examples, defaults, or dummy configuration. In general the
specific IP addresses used in Xen are not always appropriate. (For
example, 1.2.3.4 is used in a few places!)
The following addresses should be used:
* For examples and documentation, 192.0.2.0/24. (See RFC3330.)
* For defaults for private networks, a random network from RFC1918.
I have randomly selected 172.30.206.0/24 for this purpose and
documented this in at the only registry I know of,
www.ucam.org/cam-grin. This network should henceforth be used for
default configurations of local bridges, test networks, etc. in
Xen tools.
The following addresses should NOT be used:
* 10.0.*.*, 10.1.*.*, 192.168.0.*, 192.168.1.*, etc. Using these
addresses gives greatly increased likelihood of collision, as
ignorant network administrators and reckless middlebox vendors
often pick networks from the bottom of 10/8 and 192.168/16.
* 169.254.*.*. These are reserved for zeroconf (ad-hoc networking)
and should not be used for Xen private networks, bridges, etc.,
etc. Use of these addresses by Xen scripts causes trouble on hosts
(eg laptops) which find themselves in ad-hoc networking
environments. I think this is not hypothetical (!) since at least
one Linux distribution have specific code to detect this case and
cause Xen startup to fail iff the host already has an external
zeroconf address.
* 1.2.3.4. WTF !?
I have also used 127.0.255.255 in one place where apparently a dummy
address is needed (some Linux kernels won't accept a lack of an NFS
server address). If 127.0.255.255 is mistakenly used it is unlikely
to do any damage to real traffic even if it does escape into the
network at large.
Signed-off-by: Ian Jackson <ian.jackson@eu.citrix.com>
This patch implements a (non Xen-API) legacy XML-RPC interface for the
ACM commands and funnels the calls into code introduced by the Xen-API
support for ACM security management. Since some of the functionality
has changed, also the xm applications have changed. In particular the
following old commands have been removed along with some tools the
have become obsolete now:
- loadpolicy (included in: setpolicy)
- makepolicy (included in: setpolicy)
- cfgbootpolicy (included in: setpolicy)
and the following commands been introduced:
- setpolicy
- getpolicy
- resetpolicy
All tools have been adapted to work in Xen-API and legacy XML-RPC
mode. Both modes support the same functionality.
Signed-off-by: Stefan Berger <stefanb@us.ibm.com>
- recently I added an other_config field to the VTPM record which now
needs to be accounted for otherwise the test determines a bad key
- the dry-run command was throwing a different type of exception
(ACMError) than what was caught (XSMError)
- the tests based on the raw Xen-API need to build the PV_args
parameters from the old 'root' and 'extra' parameters.
Signed-off-by: Stefan Berger <stefanb@us.ibm.com>
sysctl.physinfo.nr_cpus. This also avoids miscalculation of
sockets_per_node by Xen where the number of CPUs in the system is
clipped.
From: Elizabeth Kon <eak@us.ibm.com>
Signed-off-by: Keir Fraser <keir@xensource.com>
Tests have been failing because the console for the test ramdisk wasn't using
xvc0 so testcases were not able to interact with it.
Signed-off-by: James Bulpin <james@xensource.com>
- don't reload the policy if it has been loaded
- don't always load the policy in the test suite when the policy is
already loaded
- skip tests 07 and 09 when ACM is not enabled and xm is not using the
Xen-API
- fix a problem when trying to remove an invalid label
Signed-off-by: Stefan Berger <stefanb@us.ibm.com>
This adds a couple of test cases exercising the new policy management
functionality to the security tests.
Signed-off-by: Stefan Berger <stefanb@us.ibm.com>
1) Sets a minimum of 128MB RAM for an ia64 domU; this limit was set
after experimentation, which seems to indicate it's a reasonable lower
limit (the 32MB limit previously in place did not allow an ia64 domU
to start). If there's any problem with this, I don't mind splitting
the patch and sending it to the ia64 list, but it was small, so I hope
it's okay to include it.
2) xm-test uses ramdisks built with uClibc, which doesn't compile on
ia64. I was able to create a ramdisk by hand, but as it was too
large, the resultant domU crashed after boot. This patch enables the
use of an arbitrarily large ramdisk, so long as it's uncompressed. As
xm-test builds only uncompressed ramdisks, I figured this was
reasonable for that specific application. Suggestions on how to
detect and handle a compressed ramdisk would be welcome.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Scale the memory parameter for domains using the XenAPIDomain to
create a domain. Those domains use the normal configuration where the
memory parameter is given in 'Mb', so it needs to be adapted to
'bytes'.
Signed-off-by: Stefan Berger <stefanb@us.ibm.com>
- renames the XenManagedDomain.py file to XenAPIDomain.py, since this
name better reflects its functionality/purpose
- adds domain tracking to the XenAPIDomain class so that xend-managed
domains can be deleted in an 'atexit' handler upon test case termination
- adds one basic xapi-related test which is part of the grouptests
'xapi'
- refactors the vtpm-related test using xen-api and adds it to the
grouptest 'xapi'
- adds documentation to the README for how to configure xm and xend to
use XML-RPC or Xen-API for communication
Signed-off-by: Stefan Berger <stefanb@us.ibm.com>
in a mode where all created domains a created as xend-managed domains.
This patch also fixes a problem related to calling 'xm domid' on a
currently suspended domain if that domain is a managed domain. In that
case a 'None' is returned by Xend, which I default to '-1'.
Signed-off-by: Stefan Berger <stefanb@us.ibm.com>
created as managed domains using either a parameter to the
XenTestDomain() constructor or by setting the environment variable
XM_MANAGED_DOMAINS and running the tests with it.
Signed-off-by: Stefan Berger <stefanb@us.ibm.com>
needs more thought, because people shouldn't need to set up their Xen-API server
to run the non-Xen-API bits of the test, and at the moment, you get
authentication failures on every SKIP.
Signed-off-by: Ewan Mellor <ewan@xensource.com>
similar to the XmTestDomain and XenDomain classes. I have wrapped the
xen-api for VM configuration creation, starting and stopping of VMs and
destruction of the VM configuration in the XenManagedDomain class's
methods. No device-related functions are provided through the class.
The managed domains' UUIDs are tracked and all created VMs are destroyed
upon failure or skipping of the test or by calling
xapi.vm_destroy_all().
I am adding a new grouptest 'xapi' for running xen-api tests.
Only caveat: I am using an empty username and password
(XmTestList/xapi.py) with Xend's authentication deactivated to run these
tests.
Signed-off-by: Stefan Berger <stefanb@us.ibm.com>
and extra code in hvm_vcpu_initialise(). Remove 'apic' config
option -- HVM CPUs will always have an APIC (which should be
set up in virtual wire mode for backward compatibility, just as
in a real system).
Signed-off-by: Keir Fraser <keir@xensource.com>
- it turns off verbose mode of the ACM module
- copies the test policy to the policies directory only if the directory
has been created
Signed-off-by: Stefan Berger <stefanb@us.ibm.com>
PowerPC needs console information from the command line. Resetting the whole
command line causes false failures.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
security is turned on in hypervisor. This is done by implicitly
labeling VMs and resources if they have not been labeled through
explicit calls.
To allow the xm tests suite to label resources automatically, run
./configure --enable-full-labeling
once. To turn it off, the '--enable-full-labeling' parameter should be
omitted.
Signed-off-by: Stefan Berger <stefanb@us.ibm.com>
Matthew Fioravante
Keir Fraser
Keir Fraser
Keir Fraser
James Bulpin
kfraser@localhost.localdomain
Tom Wilkie
Ewan Mellor
awilliam@xenbuild.aw
Alastair Tse
kaf24@localhost.localdomain