Do not embed IPXE into Rombios anymore. Instead, it is loaded by the
toolstack from a file as a separate module.
Ability to let user specify an IPXE blob will come later.
No user visible change.
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Acked-by: Jan Beulich <jbeulich@suse.com>
We need to choose ACPI tables properly depending on the device
model version we are running. Previously, this decision was
made by BIOS type specific code in hvmloader, e.g. always load
QEMU traditional specific tables if it's ROMBIOS and always
load QEMU Xen specific tables if it's SeaBIOS.
This change saves this behavior (for compatibility) but adds
an additional way (xenstore key) to specify the correct
device model if we happen to run a non-default one. Toolstack
bit makes use of it.
The enforcement of BIOS type depending on QEMU version will
be lifted later when the rest of ROMBIOS compatibility fixes
are in place.
Signed-off-by: Igor Druzhinin <igor.druzhinin@citrix.com>
Reviewed-by: Paul Durrant <paul.durrant@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Reviewed-by: Roger Pau Monné <roger.pau@citrix.com>
Acked-by: Jan Beulich <jbeulich@suse.com>
Commit 149c6b unmasked an issue long present in Xen: the control/event
block addresses provided in the ACPI FADT table where hardcoded to the
V1 version. This was papered over because hvmloader would also always
set HVM_PARAM_ACPI_IOPORTS_LOCATION to 1 regardless of the BIOS
version.
The most notable issue caused by the above bug was that the QEMU
traditional GPE0 block was out of sync: the address provided in the
FADT didn't match the address QEMU was using.
Note that PM1a and TMR worked fine because the V1 address was
hardcoded in the FADT and HVM_PARAM_ACPI_IOPORTS_LOCATION was
unconditionally set to 1 by hvmloader.
Fix this by passing the address of the control/event blocks to
acpi_build_tables, so the values can be properly set in the FADT table
provided to the guest.
Signed-off-by: Roger Pau Monné <roger.pau@citrix.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
We need to choose ACPI tables and ACPI IO port location
properly depending on the device model version we are running.
Previously, this decision was made by BIOS type specific
code in hvmloader, e.g. always load QEMU traditional specific
tables if it's ROMBIOS and always load QEMU Xen specific
tables if it's SeaBIOS.
This change saves this behavior (for compatibility) but adds
an additional way (xenstore key) to specify the correct
device model if we happen to run a non-default one. Toolstack
bit makes use of it.
The enforcement of BIOS type depending on QEMU version will
be lifted later when the rest of ROMBIOS compatibility fixes
are in place.
Signed-off-by: Igor Druzhinin <igor.druzhinin@citrix.com>
Reviewed-by: Paul Durrant <paul.durrant@citrix.com>
Acked-by: Andrew Cooper <andrew.cooper3@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
In prepearation to moving acpi sources into generally available
libacpi:
1. Pass IOAPIC/LAPIC/PCI mask values via struct acpi_config
2. Modify include files search paths to point to acpi directory
3. Macro-ise include file for build.c that defines various
utilities used by that file. Users of libacpi will be expected
to define this macro when compiling build.c
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Acked-by: Jan Beulich <jbeulich@suse.com>
The original code used sizeof(info->signature) as the size parameter for
memcpy, which was wrong.
Fix that by using structure assignment.
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Acked-by: Jan Beulich <jbeulich@suse.com>
... and do not include the SeaBIOS ROM into hvmloader anymore.
This also fix the dependency on roms.inc, hvmloader.o does not include it.
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Acked-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Andrew Cooper <andrew.cooper3@citrix.com>
By doing this we can move hvmloader-private interfaces (such as
uart_exists(), lpt_exists() etc.) out of the ACPI builder. This will
help us with allowing to call the builder from places other than
hvmloader.
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
In preparation for moving out ACPI builder make all
BIOSes call hvmloader_acpi_build_tables() instead of
calling ACPI code directly.
No functional changes.
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Acked-by: Jan Beulich <jbeulich@suse.com>
As recommended in http://www.gnu.org/licenses/gpl-howto.en.html.
This is the result of:
$ git grep -El Mass\|Temple\|Franklin | xargs ./fsf.pl
Where fsf.pl is:
#!/usr/bin/perl -w -pi.bak -0777
my $repl = 'If not, see <http://www.gnu.org/licenses/>.';
my $br = qr/(?:\s*\n\s*(?:[\*\#]|\/\/|\.\\" )?\s*|\s+)/;
my $inwt = qr/[Ii]f${br}not,${br}write${br}(?:to${br})?the${br}Free${br}Software${br}Foundation,(?:${br}Inc\.,)?/;
my $mass = qr/675${br}Mass${br}Ave,?${br}Cambridge,?${br}MA${br}02139,?${br}USA,?\.?/;
my $franklin = qr/51${br}Franklin${br}St(?:reet)?(?:,${br}| - )Fifth${br}Floor,?${br}Boston,?${br}MA,?${br}02110-1301,?${br}USA,?\.?/;
my $temple = qr/59${br}Temple${br}Place(?:,${br}| - )Suite${br}330,?${br}Boston,?${br}MA,?${br}021110?-1307,?${br}USA,?\.?/;
s|$inwt$br$mass|$repl|m;
s|$inwt$br$franklin|$repl|m;
s|$inwt$br$temple|$repl|m;
The only remaining mentions of these addresses are in COPYING files which I
haven't touched.
Some of the changed files are imports from elsewhere, however
filtering them out is tricky, I think it is tolerable to have these
files be modified here and then perhaps reverted on the next sync,
since it's only 1-2 lines and obvious what is going on.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
The SeaBIOS ROM image may validly exceed 128k in size, it's only our
interface code that so far assumed that it wouldn't. Remove that
restriction by setting the base address depending on image size.
Add a check to HVM loader so that too big images won't result in silent
guest failure anymore.
Uncomment the intended build-time size check for rombios, moving it
into a function so that it would actually compile.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
The emacs variable to set the C style from a local variable block is
c-file-style, not c-set-style.
Signed-off-by: David Vrabel <david.vrabel@citrix.com
Make load_rom field in struct bios_config an optionnal callback rather
than a boolean value. It allow BIOS specific code to implement it's
own option ROM loading methods.
Facilities to scan PCI devices, extract an deploy ROMs are moved into
a separate file that can be compiled optionnaly.
Signed-off-by: Julian Pidancet <julian.pidancet@gmail.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
In order to have two different DSDT tables for rombios and SeaBIOS,
this patch introduce a new parameter to acpi_build_tables() which
contain the DSDT table to load.
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Committed-by: Keir Fraser <keir@xen.org>
SeaBIOS will reserve memory in the e820 as necessary, including BIOS
data structures such as the EBDA, any tables it creates or copies into
pleace etc. Therefore arrange that the memory map provided by
hvmloader to SeaBIOS reserves only things which HVMloader has created.
Since ROMBIOS is more tightly coupled with hvmloader we retain the
ability to reserve BIOS regions in the hvmloader produced e820 and use
that from the ROMBIOS backend.
The code for this could probably have been simpler but the existing
code avoids overlapping e820 areas and so the new code does the same
(many guest OSes sanitize the e820 map to handle this, but I wouldn't
trust that all do, so I didn't take the risk)
For ROMBIOS the resulting e820 map as seen by the guest is the same
except the reserved regions at 0x9e000-0x9fc00,0x9fc00-0xa0000 are
merged into a single region 0x9e000-0xa0000 (Linux guests sanitize the
e820 to look like this anyway).
For SeaBIOS the result is that the lowmem reserved region is from
0x9f000-0xa0000 rather than 0x9e000-0xa0000 which correctly reflects
SeaBIOS's actual usage.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Build the various BIOS tables and arrange for them to be passed to
SeaBIOS. We define a simple data structure structure at a known
physical address for this purpose.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Currently we have ->bios_high_setup, which is called relatively early
and returns a cookie which is passed to ->bios_info_setup which runs
towards the end and creates the BIOS info, incorporating the cookie
which (in the case of ROMBIOS) happens to be the BIOS's high load
address . This is rather ROMBIOS specific.
Refactor to have ->bios_info_setup which is called early and prepares
the bios_info, ->bios_relocate which does any necessary relocation
(updating the BIOS info as necessary) and ->bios_info_finish which
finalises the info (e.g. by calculating the checksum).
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
SeaBIOS has functionality to load ROMs from the PCI device directly,
it makes sense to use this when it is available.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
The SeaBIOS integration here is only semi-complete and is targetted at
developers and very early adopters who can be expected to cope with
some rough edges. In particular the user must clone, patch as
necessary and compile SeaBIOS themselves since this patchset does not
cover any of that (in the same way we currently do not integrate
upstream qemu clone+build). Include a big comment to that effect next
to the Config.mk option.
Many of the bios_config callback functions are not yet used by
SeaBIOS.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Acked-by: Ian Jackson <ian.jackson.citrix.com>
Committed-by: Ian Jackson <ian.jackson.citrix.com>
Wei Liu
Igor Druzhinin
Roger Pau Monne
Boris Ostrovsky
Anthony PERARD
Ian Campbell
Jan Beulich
David Vrabel
Julian Pidancet
Keir Fraser