Now there are two control registers plus one register for
each of the 32 PHP slots. A total of 34 registers. Accordingly the
ioport space required has expanded by from 3 to 34 bytes.
Signed-off-by: Simon Horman <horms@verge.net.au>
hvmloader acpi: Use If and Else instead of Switch
Signed-off-by: Simon Horman <horms@verge.net.au>
The bcc compiler generates wrong stack pointer offset of a local
variable within ASM code if another local variable is declared
later.
Signed-off-by: Kouya Shimura <kouya@jp.fujitsu.com>
Signed-off-by: Akio Takebe <takebe_akio@jp.fujitsu.com>
The pointer to PMM function arguments must be flattened for protected
mode with zero-based segments.
Signed-off-by: Kouya Shimura <kouya@jp.fujitsu.com>
This gets rid of shenanigans with relocating the jump table around the
place.
Also clean up bios_info table while we are updating it.
Signed-off-by: Keir Fraser <keir.fraser@citrix.com>
Since it is a build prerequisite (in some cases) simply fail the build
if it is not found when it turns out to be required. Just as we would
for any other tool-chain prereq.
Signed-off-by: Keir Fraser <keir.fraser@citrix.com>
The rombios always becomes read-only after using 32bit gateway.
That is not handy for using the gateway.
Signed-off-by: Kouya Shimura <kouya@jp.fujitsu.com>
* enables linear framebuffer and VBE 3.0 extensions.
* add a number of new resolutions, up to 2560x1600, and including
* widescreen modes common to modern displays.
* Introduce configurable video ram size through the "videoram" config
* file option, shrinking default video ram used to 4 Megs (thus
* eliminating 4 wasted megs/VM that have been the case until now), but
* allowing users to specify up to 16 Megs of vram, to support the
* extreme high resolutions such as 2560x1600x32.
Signed-off-by: Trolle Selander <trolle.selander@eu.citrix.com>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
without deferring the test execution of CC. This avoids extra
executions of CC every time CFLAGS is expanded.
Signed-off-by: Keir Fraser <keir.fraser@citrix.com>
dev_memsize ends up 0 when it shouldn't be on 16G boundary conditions.
Signed-off-by: Bill Rieske <brieske@novell.com>
Signed-off-by: Keir Fraser <keir.fraser@citrix.com>
This has finally bugged me enough to do something about it:
make prints `***' when it stops due to an error. With make -j, and/or
with automated build systems, this error marker can be in the middle
of a large logfile. It is useful to be able to search for it.
Therefore change occurrences of `*' to `=' for information and warning
messages. `***' is reserved for cases where the build stops.
A corresponding change is being applied to qemu-xen-unstable.
Signed-off-by: Ian Jackson <ian.jackson@eu.citrix.com>
If you use -MMD -MF then the correct .o filename is written to the
.*.d file as the compiler driver arranges everything. This was done
in 19010:275abe1c5d24 for the hypervisor.
In this patch we do the same elsewhere in the xen-unstable tree,
particularly tools/. Specifically:
* Change tools/Rules.mk to add -MMD -MF ... to CFLAGS and set DEPS.
* Remove -Wp,-MD... from every other Makefile
* Remove setting of DEPS from every other Makefile
* Ensure that every Makefile says -include $(DEPS)
* Ensure that every Makefile's clean target removes $(DEPS)
Some Makefiles were already halfway there, but often for a different
variable name eg PROG_DEP. The variable name is now standardised in
Rules.mk as DEPS.
I have done a test build with this change, on Debian etch.
Signed-off-by: Ian Jackson <ian.jackson@eu.citrix.com>
To make memory management easier in hvmloader, defer building a
generic E820 map until the end of hvmloader bootstrap.
Signed-off-by: Keir Fraser <keir.fraser@citrix.com>
hvm_info_table to describe memory parameters in a simpler form from
domain builder to hvmloader.
Also move reserved special page mappings immediately below the 4GB
boundary.
Signed-off-by: Keir Fraser <keir.fraser@citrix.com>
I have copied the tarballs that the xen-unstable build downloads to
xenbits.xensource.com (which also hosts our hg and git). This patch
changes the download URLs to use that location.
That way the build will depend on only one external machine, under one
administration, rather than many. Also it means that the build won't
break if these sites become permanently unavailable or are rearranged
and we don't run a risk of having to panic and beg if a file should go
missing.
Signed-off-by: Ian Jackson <ian.jackson@eu.citrix.com>
In DSDT, reserve the IO port ranges: [0x10c0, 0x10c2] and [0xb044,
0xb047] that are used by the virtual PCI hotplug.
Or else, for a hotplugged-in device, the port IO BAR assigned by guest
OS may conflict with the ranges here.
Signed-off-by: Dexuan Cui <dexuan.cui@intel.com>
Extended Bios Data Area (EBDA) can be relocated by the initialization
of PCI option ROM. The IPL boot table is also.
EBDA must be accessed via 0x40E after the initialization.
Signed-off-by: Kouya Shimura <kouya@jp.fujitsu.com>
When a VMX guest tries to enter real mode, put it in virtual 8086 mode
instead, if that's possible. Handle all errors and corner cases by
falling back to the real-mode emulator.
This is similar to the old VMXASSIST system except it uses Xen's
x86_emulate emulator instead of having a partial emulator in the guest
firmware. It more than doubles the speed of real-mode operation on
VMX.
Signed-off-by: Tim Deegan <Tim.Deegan@citrix.com>
BIOS. Current Xen hard coded VGA ROM at 0xC0000 and etherboot ROM
at 0xD0000. This makes the space in [0xC0000 - 0xDFFFF] to be
fragments, which makes it hard to find enough space to hold another
Option ROM.
Signed-off-by: Shan Haitao <haitao.shan@intel.com>
Keir Fraser