Use expect to invoke QEMU so that we can terminate the test as soon as
we get the right string in the output instead of waiting until the
final timeout.
For timeout, instead of an hardcoding the value, use a Gitlab CI
variable "QEMU_TIMEOUT" that can be changed depending on the latest
status of the Gitlab CI runners.
Signed-off-by: Stefano Stabellini <stefano.stabellini@amd.com>
Reviewed-by: Michal Orzel <michal.orzel@amd.com>
The serial is already setup by the firmware, be consistent with the rest of the
QEMU tests and don't specify a com1 setup.
Note it's also bogus, as the extra ',' will make the intended DPS argument to
be parsed as the io-base.
Signed-off-by: Roger Pau Monné <roger.pau@citrix.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
We can add qemu into the container so that there's no need to install
it everytime we run a test.
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Reviewed-by: Andrew Cooper <andrew.cooper3@citrix.com>
Xen is now built without CONFIG_PV32 by default and thus test jobs
"qemu-smoke-x86-64-gcc" and "qemu-smoke-x86-64-clang" fails because
they are using XTF's "test-pv32pae-example" which is an hello word
32bit PV guest.
As we are looking for whether Xen boot or not with a quick smoke test,
just use 64bit tests instead.
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Reviewed-by: Andrew Cooper <andrew.cooper3@citrix.com>
10s is too low for the clang tests, this is the output from a clang
test:
(XEN) [ 6.512748] ***************************************************
(XEN) [ 6.513323] SELFTEST FAILURE: CORRECT BEHAVIOR CANNOT BE GUARANTEED
(XEN) [ 6.513891] ***************************************************
(XEN) [ 6.514469] 3... 2... 1...
(XEN) [ 9.520011] *** Serial input to DOM0 (type 'CTRL-a' three times to switch input)
(XEN) [ 9.544319] Freed 488kB init memory
--- Xen Test Framework ---
Environment: HVM 32bit (PAE 3 levels)
Hello World
Test result: SUCCESS
(XEN) [ 9.610977] Hardware Dom0 halted: halting machine
As can be seen from the output above booting Xen and the XTF test
takes ~10s, without accounting for the time it takes for QEMU to
initialize.
Increase the timeout to 30s to be on the safe side.
Signed-off-by: Roger Pau Monné <roger.pau@citrix.com>
Acked-by: Andrew Cooper <andrew.cooper3@citrix.com>
Acked-by: Wei Liu <wl@xen.org>
Release-acked-by: Juergen Gross <jgross@suse.com>
Enable Xen timestamps in the automated Xen tests, this is helpful in
order to figure out if Xen is stuck or just slow in the automated
tests.
Signed-off-by: Roger Pau Monné <roger.pau@citrix.com>
Acked-by: Andrew Cooper <andrew.cooper3@citrix.com>
Acked-by: Wei Liu <wl@xen.org>
Release-acked-by: Juergen Gross <jgross@suse.com>
Make qemu-smoke-x86-64.sh take a variant argument. Make two new tests
in test.yaml.
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Acked-by: Doug Goldstein <cardoe@cardoe.com>
Release-acked-by: Juergen Gross <jgross@suse.com>
This patch introduces a new test stage into the pipeline and provides
a simple QEMU based smoke test.
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Acked-by: Doug Goldstein <cardoe@cardoe.com>
Stefano Stabellini