The domain name stored in /local/domain/$domid/name is simpler to
access and is the only domain name modified by "xl rename". Use this
domain name in libxenstat's reporting.
Signed-off-by: Daniel De Graaf <dgdegra@tycho.nsa.gov>
Acked-by: Ian Jackson <ian.jackson@eu.citrix.com>
Committed-by: Ian Jackson <ian.jackson@eu.citrix.com>
Switch to recently released 1.6.3.2 from upstream. This incorporates all the
changesets which we previously applied to 1.6.3.1.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Committed-by: Ian Jackson <ian.jackson@eu.citrix.com>
Check for a curses compatible library (curses or ncurses basically).
One of those is needed to compile Xen tools (gtraceview and xentop).
Modify Makefiles/sources to use configure output (fetch CURSES_LIBS
from tools/Tools.mk and header to include from tools/config.h)
Signed-off-by: Roger Pau Monne <roger.pau@entel.upc.edu>
Acked-by: Ian Jackson <ian.jackson@eu.citrix.com>
Committed-by: Ian Jackson <ian.jackson@eu.citrix.com>
The ARM doesn't actually say that the WFI instruction will return
immediately if CPSR.I is clear and an instruction is pending, but
this seems to match up with how linux uses it.
Signed-off-by: Tim Deegan <tim@xen.org>
Committed-by: Ian Campbell <ian.campbell@citrix.com>
The boot CPU turns on W^X in setup_pagetables(). Do the same for other
CPUs after they boot. If we go to per-CPU pagetables, this is where
that will happen.
Signed-off-by: Tim Deegan <tim@xen.org>
Committed-by: Ian Campbell <ian.campbell@citrix.com>
Reboot runes grabbed from linux's SP810 reset function.
Doesn't seem to work on the model, though.
Signed-off-by: Tim Deegan <tim@xen.org>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Committed-by: Ian Campbell <ian.campbell@citrix.com>
Secondary CPUs come up directly onto the stack of the appropriate idle
vcpu; the boot CPU starts on a statically allocated stack and switches
over to the idle vcpu's one once the idle domain has been built.
Signed-off-by: Tim Deegan <tim@xen.org>
Committed-by: Ian Campbell <ian.campbell@citrix.com>
Bring non-boot CPUs up as far as running on the relocated pagetables,
one at a time, before the non-relocated copy of Xen gets reused for
general memory pools.
Don't yet bring them up into C; that will happen later when stacks are
allocated.
Signed-off-by: Tim Deegan <tim@xen.org>
Committed-by: Ian Campbell <ian.campbell@citrix.com>
Otherwise we get a deadlock between the p2m lock and the event lock,
which handle_mmio() acquires.
Signed-off-by: Tim Deegan <tim@xen.org>
Acked-by: Andres Lagar-Cavilla <andres@lagarcavilla.org>
This limits the ability of the guest to play around with its own rings, and DoS
itself.
Signed-off-by: Andres Lagar-Cavilla <andres@lagarcavilla.org>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Committed-by: Tim Deegan <tim@xen.org>
Otherwise we wind up with zombie domains, still holding onto refs to the mem
event ring pages.
Signed-off-by: Andres Lagar-Cavilla <andres@lagarcavilla.org>
Acked-by: Tim Deegan <tim@xen.org>
Committed-by: Tim Deegan <tim@xen.org>
Now that we have an interface close to finalizing, do the necessary plumbing to
set up a ring for reporting failed allocations in the unshare path.
Signed-off-by: Andres Lagar-Cavilla <andres@lagarcavilla.org>
Acked-by: Tim Deegan <tim@xen.org>
Committed-by: Tim Deegan <tim@xen.org>
This solves a long-standing issue in which the pages backing these rings were
pages belonging to dom0 user-space processes. Thus, if the process would die
unexpectedly, Xen would keep posting events to a page now belonging to some
other process.
We update all API-consumers in tree (xenpaging and xen-access).
This is an API/ABI change, so please speak up if it breaks your accumptions.
The patch touches tools, hypervisor x86/hvm bits, and hypervisor x86/mm bits.
Signed-off-by: Andres Lagar-Cavilla <andres@lagarcavilla.org>
Acked-by: Tim Deegan <tim@xen.org>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Committed-by: Tim Deegan <tim@xen.org>
These are currently used for the rings connecting Xen with qemu. Refactor them
so the same code can be later used for mem event rings.
Signed-off-by: Andres Lagar-Cavilla <andres@lagarcavilla.org>
Acked-by: Tim Deegan <tim@xen.org>
Committed-by: Tim Deegan <tim@xen.org>
Don't use the superfluous shared page, return the event channel directly as
part of the domctl struct, instead.
In-tree consumers (xenpaging, xen-access) updated. This is an ABI/API change,
so please voice any concerns.
Known pending issues:
- pager could die and its ring page could be used by some other process, yet
Xen retains the mapping to it.
- use a saner interface for the paging_load buffer.
This change also affects the x86/mm bits in the hypervisor that process the
mem_event setup domctl.
Signed-off-by: Andres Lagar-Cavilla <andres@lagarcavilla.org>
Acked-by: Tim Deegan <tim@xen.org>
Acked-by: Olaf Hering <olaf@aepfle.de>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Committed-by: Tim Deegan <tim@xen.org>
Calling XENPF_set_processor_pminfo with XEN_PM_CX could cause states
array in "struct acpi_processor_power" to exceed its limit.
The array used to be reset (by function cpuidle_init_cpu()) for each
hypercall. The patch puts it back that way and adds an assertion to
make it clear in case that happens again.
Signed-off-by: Eric Chanudet <eric.chanudet@eu.citrix.com>
- convert assertion to printk() & bail
- eliminate struct acpi_processor_cx's valid member (not read anymore)
- further adjustments to one-time-only vs each-time operations in
cpuidle_init_cpu()
- don't use ACPI_STATE_Cn as array index anymore
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Acked-by: Keir Fraser <keir@xen.org>
Passing both a struct vcpu pointer and the corresponding struct domain
one is simply pointless, especially when intermediate functions just
forward it without themselves making use of the already obtained value.
Also constify a few function parameters.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Acked-by: Keir Fraser <keir@xen.org>
Introduce a command parameter to set the watchtog timeout. Manually
specifying "watchdog_timeout=<seconds>" on the command line will also
turn the watchdog on. For consistency, move opt_watchdog into nmi.c
along with opt_watchdog_timeout.
Signed-off-by: Andrew Cooper <andrew.cooper3@citrix.com>
Committed-by: Keir Fraser <keir@xen.org>
Win2k8 x64 reads this MSR on revF chips, where it wasn't publically
available; it uses a magic constant in %rdi as a password, which we
don't have in rdmsr_safe(). Since we'll ignore the later writes, just
use a plausible value here (the reset value from rev10h chips) if the
real CPU didn't provide one.
Signed-off-by: George Dunlap <george.dunlap@eu.citrix.com>
Committed-by: Keir Fraser <keir@xen.org>
This patch should clarify which of the two possible reasons cause the
messages
of the form "(XEN) mm.c:908:d1 Error getting mfn 29b2b (pfn
5555555555555555)
from L1 entry 0000000029b2b067 for l1e_owner=1, pg_owner=1".
Signed-off-by: George Dunlap <george.dunlap@eu.citrix.com>
Committed-by: Keir Fraser <keir@xen.org>
All three per-architecture implementations were identical, and I cannot
see how future architectures would need any sort of customization here
(the only per-architecture aspect here is the actual PAGE_SHIFT value).
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Acked-by: Keir Fraser <keir@xen.org>
Still a work in progress, but submitted as a start.
Changes since v1:
- Include all up to date information from the wiki.
Signed-off-by: Andrew Cooper <andrew.cooper3@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Committed-by: Keir Fraser <keir@xen.org>
xen/Makefile is designed to allow the user to supply a file named
xen/xen-include to change the format of xen version strings.
Unfortunately, "make clean" removes xen/xen*, which will remove this
file.
Make the clean process more targeted.
Signed-off-by: George Dunlap <george.dunlap@eu.citrix.com>
Committed-by: Keir Fraser <keir@xen.org>
We already have xenversion as a target in the xen subdirectory;
simply extend it so that "make xenversion" does what you'd expect.
Signed-off-by: George Dunlap <george.dunlap@eu.citrix.com>
Committed-by: Keir Fraser <keir@xen.org>
Use a timer to emulate update cycle. The timer runs only when AIE is
set.
Signed-off-by: Yang Zhang <yang.z.zhang@Intel.com>
Committed-by: Keir Fraser <keir@xen.org>
Use a timer to emulate update cycle. When update cycle ended and UIE
is set, raise an interrupt. The timer runs only when AF is cleared.
Signed-off-by: Yang Zhang <yang.z.zhang@Intel.com>
Committed-by: Keir Fraser <keir@xen.org>
The UIP(update in progress) is set when RTC is in updating. And the
update cycle begins 244us later after UIP is set.
Signed-off-by: Yang Zhang <yang.z.zhang@Intel.com>
Committed-by: Keir Fraser <keir@xen.org>
Daniel De Graaf
Wei Liu
Andres Lagar-Cavilla
Ian Campbell
Ian Jackson
Roger Pau Monne
Tim Deegan
Keir Fraser
Jan Beulich
Eric Chanudet
Andrew Cooper
George Dunlap
Yang Zhang