Because there is not necessarily any lock held at the point the
application (eg, libvirt) calls libxl_osevent_occurred_timeout and
..._fd, in a multithreaded program those calls may be arbitrarily
delayed in relation to other activities within the program.
libxl therefore needs to be prepared to receive very old event
callbacks. Arrange for this to be the case for fd callbacks.
This requires a new layer of indirection through a "hook nexus" struct
which can outlive the libxl__ev_foo. Allocation and deallocation of
these nexi is mostly handled in the OSEVENT macros which wrap up
the application's callbacks.
Document the problem and the solution in a comment in libxl_event.c
just before the definition of struct libxl__osevent_hook_nexus.
There is still a race relating to libxl__osevent_occurred_timeout;
this will be addressed in the following patch.
Reported-by: Bamvor Jian Zhang <bjzhang@suse.com>
Cc: Bamvor Jian Zhang <bjzhang@suse.com>
Cc: Ian Campbell <Ian.Campbell@citrix.com>
Tested-by: Jim Fehlig <jfehlig@suse.com>
Acked-by: Jim Fehlig <jfehlig@suse.com>
Signed-off-by: Ian Jackson <ian.jackson@eu.citrix.com>
Committed-by: Ian Campbell <ian.campbell@citrix.com>
Introduce a function to map a range of physical memory into Xen virtual
memory.
It doesn't need domheap to be setup.
It is going to be used to map the videoram.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Committed-by: Ian Campbell <ian.campbell@citrix.com>
Add flush_xen_data_tlb_range_va, that flushes a range of virtual addresses.
Replace all the calls to flush_xen_data_tlb_va with calls to
flush_xen_data_tlb_range_va and remove flush_xen_data_tlb_va.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Committed-by: Ian Campbell <ian.campbell@citrix.com>
Raise the RTC IRQ not only when UIE gets set while UF was already set,
but generalize this to cover AIE and PIE as well.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Acked-by: Keir Fraser <keir@xen.org>
Properly mask off bit 7 when retrieving the hour values in
alarm_timer_update(), and properly use RTC_HOURS_ALARM's bit 7 when
converting from 12- to 24-hour value.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Acked-by: Keir Fraser <keir@xen.org>
Don't look at RTC_PIE in rtc_timer_update(), and hence don't call the
function on REG_B writes at all.
Also handle the two other possible clock bases.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Acked-by: Keir Fraser <keir@xen.org>
Note that in the RTC_UIE/RTC_UF case, this also fixes the lack of
setting RTC_IRQF.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Acked-by: Keir Fraser <keir@xen.org>
This mainly involves adjusting the number of L4 entries needing copying
between page tables (which is now different between PV and HVM/idle
domains), and changing the cutoff point and method when more than the
supported amount of memory is found in a system.
Since TMEM doesn't currently cope with the full 1:1 map not always
being visible, it gets forcefully disabled in that case.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Acked-by: Keir Fraser <keir@xen.org>
Acked-by: Dan Magenheimer <dan.magenheimer@oracle.com>
Despite the changes below, tmem still has code assuming to be able to
directly access all memory, or mapping arbitrary amounts of not
directly accessible memory. I cannot see how to fix this without
converting _all_ its domheap allocations to xenheap ones. And even then
I wouldn't be certain about there not being other cases where the "all
memory is always mapped" assumption would be broken. Therefore, tmem
gets disabled by the next patch for the time being if the full 1:1
mapping isn't always visible.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Acked-by: Dan Magenheimer <dan.magenheimer@oracle.com>
Acked-by: Keir Fraser <keir@xen.org>
This eliminates a couple of incorrect/inconsistent uses of
map_domain_page() from VT-x code.
Note that this does _not_ add error handling where none was present
before, even though I think NULL returns from any of the mapping
operations touched here need to properly be handled. I just don't know
this code well enough to figure out what the right action in each case
would be.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Acked-by: Keir Fraser <keir@xen.org>
This involves no longer storing virtual addresses of the per-domain
mapping L2 and L3 page tables.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Acked-by: Keir Fraser <keir@xen.org>
So far this has been repeated in 3 places, requiring to remember to
update all of them if a change is being made.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
This requires a minor hack to allow the correct page tables to be used
while running on Dom0's page tables (as they can't be determined from
"current" at that time).
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Acked-by: Keir Fraser <keir@xen.org>
This is being done mostly in the form previously used on x86-32,
utilizing the second L3 page table slot within the per-domain mapping
area for those mappings. It remains to be determined whether that
concept is really suitable, or whether instead re-implementing at least
the non-global variant from scratch would be better.
Also add the helpers {clear,copy}_domain_page() as well as initial uses
of them.
One question is whether, to exercise the non-trivial code paths, we
shouldn't make the trivial shortcuts conditional upon NDEBUG being
defined. See the debugging patch at the end of the series.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Acked-by: Keir Fraser <keir@xen.org>
... to allow frames for up to 16Tb.
At the same time, add the super page frame table coordinates to the
comment describing the address space layout.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Acked-by: Keir Fraser <keir@xen.org>
There is no reason for this and doing so exposes a memory leak to
guests. Only toolstacks need write access to this HVM param.
This is XSA-35 / CVE-2013-0152.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Acked-by: Jan Beulich <JBeulich@suse.com>
Committed-by: Jan Beulich <jbeulich@suse.com>
Fix S3 regression introduced by cs 23013:65d26504e843 (ACPI: large
cleanup). The dmar virtual pointer returned from acpi_get_table cannot
be safely stored away and used later, as the underlying
acpi_os_map_memory / __acpi_map_table functions overwrite the mapping
causing it to point to different tables than dmar (last fetched table is
used). This subsequently causes acpi_dmar_reinstate() and
acpi_dmar_zap() to write data to wrong table, causing its corruption and
problems with consecutive s3 resumes.
Added a new function to fetch ACPI table physical address, and
establishing separate static mapping for dmar_table pointer instead of
using acpi_get_table().
Signed-off-by: Tomasz Wroblewski <tomasz.wroblewski@citrix.com>
Added call to acpi_tb_verify_table(). Fixed page count passed to
map_pages_to_xen(). Cosmetic changes.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Committed-by: Jan Beulich <jbeulich@suse.com>
Manipulation of a domain's pirq namespace was not fully protected by
XSM hooks because the XSM hooks for IRQs needed a physical IRQ. Since
this may not apply to HVM domains, a complete solution needs to split
the XSM hook for this operation, using one hook for the PIRQ
manipulation and one for controlling access to the hardware IRQ.
This reworking has the advantage of providing the same MSI data to
remove_irq that is provided to add_irq, allowing the PCI device to be
determined in both functions. It also eliminates the last callers of
rcu_lock_target_domain_by_id in x86 and common code in preparation for
this function's removal.
Signed-off-by: Daniel De Graaf <dgdegra@tycho.nsa.gov>
Committed-by: Keir Fraser <keir@xen.org>
These hypercalls are usable by HVM guests. Once connected, simple
functions of the Xen toolstack can be run from an HVM domain if that
domain is permitted access (which is currently only possible via XSM).
Signed-off-by: Daniel De Graaf <dgdegra@tycho.nsa.gov>
Committed-by: Keir Fraser <keir@xen.org>
c/s 22949:54fe1011f86b removed the forwarding of NMIs to Dom0 when they
were caused by PCI SERR. NMI buttons as well as BMCs (like HP's iLO)
may however want such events to be seen in Dom0 (e.g. to trigger a
dump).
Therefore restore most of the functionality which named c/s removed
(adjusted for subsequent changes, and adjusting the public interface to
use the modern term, retaining the old one for backwards
compatibility).
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Acked-by: Keir Fraser <keir@xen.org>
Correct format string, fixing:
vtpm_storage.c: In function 'vtpm_storage_load_header': vtpm_storage.c:658: error: format '%ld' expects type 'long int', but argument 5 has type 'unsigned int'
vtpm_storage.c:658: error: format '%ld' expects type 'long int', but argument 5 has type 'unsigned int' make[2]: *** [vtpm_storage.o] Error 1
Add padlock.o to PSSL_OBJS, fixing:
/local/scratch/ianc/devel/xen-unstable.git/stubdom/mini-os-x86_32-vtpmmgr/mini-os.o: In function `aes_crypt_ecb': /local/scratch/ianc/devel/xen-unstable.git/stubdom/polarssl-x86_32/library/aes.c:659: undefined reference to `padlock_supports'
/local/scratch/ianc/devel/xen-unstable.git/stubdom/polarssl-x86_32/library/aes.c:661: undefined reference to `padlock_xcryptecb' /local/scratch/ianc/devel/xen-unstable.git/stubdom/mini-os-x86_32-vtpmmgr/mini-os.o: In function `aes_crypt_cbc': /local/scratch/ianc/devel/xen-unstable.git/stubdom/polarssl-x86_32/library/aes.c:771: undefined reference to `padlock_supports'
/local/scratch/ianc/devel/xen-unstable.git/stubdom/polarssl-x86_32/library/aes.c:773: undefined reference to `padlock_xcryptcbc'
make[1]: ***
[/local/scratch/ianc/devel/xen-unstable.git/stubdom/mini-os-x86_32-vtpmmgr/mini-os]
Error 1
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Acked by: Matthew Fioravante <matthew.fioravante@jhuapl.edu>
[ ijc -- applied same fix to stubdom/vtpm/Makefile ]
Committed-by: Ian Campbell <ian.campbell@citrix.com>
After memcpy'ing the kernel in guest memory we need to flush the dcache
to make sure that the data actually reaches the memory before we start
executing guest code with caches disabled.
copy_from_paddr is the function that does the copy, so add a
flush_xen_dcache_va_range there.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Committed-by: Ian Campbell <ian.campbell@citrix.com>
Fallback to xen,dom0-bootargs if this isn't present.
Ideally this would use module1-args iff the kernel came from the
modules and the existing xen,dom0-bootargs if the kernel came from
flash, but this approach is simpler and has the same effect in
practice.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Acked-by: Tim Deegan <tim@xen.org>
Committed-by: Ian Campbell <ian.campbell@citrix.com>
This will still fail if the modules are such that Xen is pushed out of
the top 32M of RAM since it will then overlap with the domheap (or
possibly xenheap). This will be dealt with later.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Acked-by: Tim Deegan <tim@xen.org>
Committed-by: Ian Campbell <ian.campbell@citrix.com>
The intention is that these will eventually be filled in with
information from the bootloader, perhaps via a DTB binding.
Allow for 2 modules (kernel and initrd), plus a third pseudo-module
which is the hypervisor itself. Currently we neither parse nor do
anything with them.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Committed-by: Ian Campbell <ian.campbell@citrix.com>
I forgot to do this while checking in 26424:e1d7053e4d45. Refresh now
so as to not cause confusing looking changes next time it is run.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Committed-by: Ian Campbell <ian.campbell@citrix.com>
When the guest writes one field of the RTC time, we must bring all the
other fields up to date for the current second before calculating the
new RTC time.
Signed-off-by: Tim Deegan <tim@xen.org>
Tested-by: Phil Evans <Phil.Evans@m247.com>
Committed-by: Jan Beulich <jbeulich@suse.com>
In some cases BIOS may not enable WC+ memory type on family 10 processors,
instead converting what would be WC+ memory to CD type. On guests using
nested pages this could result in performance degradation. This patch
enables WC+.
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@amd.com>
Committed-by: Jan Beulich <jbeulich@suse.com>
Stub domains now use autoconf to build.
This configure script can enable or disable specific domains
and also specify custom download locations for stubdom library
packages. See ./configure --help for details.
C and Caml are disabled by default. vtpm-stubdom is conditional
on the presense of cmake.
Rename vtpmmgrdom to vtpmmgr-stubdom
Also update .*ignore
Signed-off-by: Matthew Fioravante <matthew.fioravante@jhuapl.edu>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Committed-by: Ian Campbell <ian.campbell@citrix.com>
Add 3 new libraries to stubdom:
libgmp
polarssl
Berlios TPM Emulator 0.7.4
Add makefile structure for vtpm and vtpmmgrdom. Both
vtpm domains are optional builds as vtpm depends on
cmake. To build either of them, you must do so explicitly.
make vtpm-stubdom vtpmmgrdom
Finally, also update .*ignore
Signed-off-by: Matthew Fioravante <matthew.fioravante@jhuapl.edu>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
[ijc, folded in fix from Matthew to workaround cmake 2.8.2 build failure]
Committed-by: Ian Campbell <ian.campbell@citrix.com>
Ian Jackson
Stefano Stabellini
Tim Deegan
Jan Beulich
Ian Campbell
Tomasz Wroblewski
Daniel De Graaf
Boris Ostrovsky
Matthew Fioravante