parse HVM e820 tables in Xen (add some extra HVM parameters as a
cleaner alternative). Lots of code removal.
Signed-off-by: Keir Fraser <keir@xensource.com>
Do not output image, security if they are empty
Change xm list slightly to be more informative about state.
Add back store_mfn and console_mfn to the SXP so save/restore can work
again.
Signed-off-by: Alastair Tse <atse@xensource.com>
older kernels.
On some older kernels the CHECKSUM_UNNECESSARY flag on received
skbuffs is not honoured by all subsystems, specifically netfilter
under 2.6.9-42.EL
To work around this we need to ensure that the correct checksum is
calculated at some point. We can cause the backend to do this for us
by advertising to the backend that we cannot support checksum offload.
The correlation of this issue with the presence of NETIF_F_TSO is not
100% but it is a good first approximation.
Signed-off-by: Ian Campbell <ian.campbell@xensource.com>
call_usermodehelper_keys() was not available until 2.6.13 but since we
pass session_keyring as NULL we may as well use call_usermodehelper()
anyway.
Signed-off-by: Ian Campbell <ian.campbell@xensource.com>
We used to park a capped VCPU when it had ran its fair share, even
if the fair share was below its cap. With this change, make sure
we only park once a VCPU has overrun its actual cap.
We could also try to make the capping mechanism more accurate by
parking and unparking at a finer granularity (currently done on
30ms boundaries) but that'll be for a different time.
Signed-off-by: Emmanuel Ackaouy <ack@xensource.com>
Allocate HVM guest memory in the libxc builder function rather
than in xend. Clean up fall out from these changes.
Todo: Fix ia64. Move PV builder to same model (it should allocate the
memory rather than xend doing so -- then it can avoid using
xc_get_pfn_list()).
Signed-off-by: Keir Fraser <keir@xensource.com>
This cleans up HVM start-of-day in Xen and means that the
HVM status of a domain is maintained from cradle to grave.
Signed-off-by: Keir Fraser <keir@xensource.com>
dom0_mem=[min:<min_amt>,][max:<max_amt>,][<amt>]
<min_amt>: The minimum amount of memory which should be allocated for dom0.
<max_amt>: The maximum amount of memory which should be allocated for dom0.
<amt>: The precise amount of memory to allocate for dom0.
Notes:
1. <amt> is clamped from below by <min_amt> and from above by available
memory and <max_amt>
2. <min_amt> is clamped from above by available memory and <max_amt>
3. <min_amt> is ignored if it is greater than <max_amt>
4. If <amt> is not specified, it is calculated as follows:
"All of memory is allocated to domain 0, minus 1/16th which is reserved
for uses such as DMA buffers (the reservation is clamped to 128MB)."
Each value can be specified as positive or negative:
If +ve: The specified amount is an absolute value.
If -ve: The specified amount is subtracted from total available memory.
Signed-off-by: Keir Fraser <keir@xensource.com>
Also, clean up the shadow *_propagate/fault routines.
This allows us to quickly dispatch some guest-not-present faults
and most MMIO accesses without taking the shadow lock.
Signed-off-by: Tim Deegan <Tim.Deegan@xensource.com>
Guest physical addresses are not guaranteed to fit in either a pointer
or an unsigned long int; use paddr_t for them.
Signed-off-by: Tim Deegan <Tim.Deegan@xensource.com>
directory pending tighter integration of table generation
into hvmloader. This patch also includes the TPM TIS SSDT
generator from Stefan Berger at IBM.
Signed-off-by: Keir Fraser <keir@xensource.com>
channel upcalls.
The issue here was that the Xen platform PCI interrupt is only updated
when you return from the hypervisor into guest context, and so remained
asserted for a short interval after the interrupt handler ran. If
it happened that the first subsequent trap to the hypervisor was
for unmasking the 8259 interrupt again, the unmasking caused the interrupt
to be reinjected. This caused an edge on the chaining interrupt from
the slave PIC to the master. The platform interrupt on the slave
would then be cleared as we returned to the guest, and so you
eventually end up injecting an interrupt on the master chained
interrupt with nothing pending on the slave, which shows up as
a spurious interrupt in the guest.
Signed-off-by: Steven Smith <sos22@cam.ac.uk>
domains with PV drivers loaded. This patch creates a new PV-on-HVM
module, reboot.ko, which, when loaded, creates control/reboot_module
in the store. The tools notice this, and disable the watch which would
normally destroy HVM domains which are the target of an xm shutdown
command, allowing the reboot module to shut the domain down cleanly.
Signed-off-by: Tetsu Yamamoto <yamamoto.tetsu@jp.fujitsu.com>
(Checkin comments by Steven Smith <sos22@cam.ac.uk>)
